Hobart-welding-products AirForce 250ci Uživatelský manuál

AirForce 250ciAnd HP-25 TorchProcessesDescriptionAir Plasma CuttingAir Plasma CutterOM-230 455C 2007-07™File: Plasma Cutters

OM-230 455 Page 6 N’approchez pas le tube du chalumeau et l’arc pilote lorsque la gâ-chette est enfoncée. Le câble de masse doit être pincé correcte

OM-230 455 Page 7 Les bouteilles ne doivent pas être près de la zone de coupage ni detout autre circuit électrique. Un contact électrique ne doit ja

OM-230 455 Page 8LE COUPAGE Ã L’ARC peut causerdes interférence. L’énergie électromagnétique peut gêner le fonction-nement d’appareils électroniques

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 9SECTION 3 − DEFINITIONS3-1. Symbols And Definitions For Nameplate And Se

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 10SECTION 4 − INSTALLATION4-1. Specifications For Power SourcePrimaryVolt

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 114-4. Torch Dimensions And WeightRef. 801 397-A3.0 lb (1.4 kg)1 in(25mm

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 124-6. Connecting Work Clamp Do not connect work clamp tothe portion of

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 134-9. Connecting Input PowerRef. 804 852-A / Ref. 803 766-BCheck input v

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 144-11. Cable Management Strap804 885-A1 Cable Management StrapCoil cable

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 15SECTION 5 − OPERATION5-1. Controls2 230 442-B11 Power SwitchThe cooling

Hobart Welders manufactures a full lineof welders and welding related equipment.For information on other quality Hobart products, contact your local H

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 16Ref 803 915-A / Ref. 804 848-A5-3. Plasma Cutting System PracticesPulli

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 17804 848-A5-4. Sequence Of Cutting OperationEXAMPLE Of Cutting Operation

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 18Ref. 804 848-A5-5. Sequence Of Cutting Using Stand-off GuideEXAMPLE Of

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 19Ref. 803 640-A / 801 400-B5-6. Sequence Of Piercing OperationConnect wo

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 20SECTION 6 − MAINTENANCE & TROUBLESHOOTING6-1. Routine Maintenance

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 216-2. Trouble Lights And Checking Shield Cup Shutdown System1 Power Ligh

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 226-3. Checking/Replacing Retaining Cup, Tip, And ElectrodeA good practic

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 236-4. Compressor Filter Cleaning And Replacement Turn Off power source,

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 246-5. Torch And Work Cable Connections Turn Off power source, anddiscon

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 256-6. Troubleshooting Power SourceConnect unit to proper inputvoltage. (

TABLE OF CONTENTSSECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol

 A complete Parts List is available at www.HobartWelders.comOM-230 455 Page 266-7. Troubleshooting TorchTorch travel speed too slow;increase travel s

OM-230 455 Page 27SECTION 7 − ELECTRICAL DIAGRAM230 449-BFigure 7-1. Circuit Diagram

OM-230 455 Page 28SECTION 8 − PARTS LIST8-1. Recommended Spare PartsDescriptionPartNo.ItemNo.Recommended Spare PartsQuantityDia.Mkgs.232 647 TORCH, HP

Notes229895MATERIAL THICKNESS GAUGE

Notes

Warranty Questions?Call1-800-332-32817 AM − 6 PM ESThobart_warr 2007−01ServiceYou always get the fast,reliable response youneed. Most replacementparts

PRINTED IN USA © 2007 Hobart Welding Products.2007−01Hobart Welding ProductsAn Illinois Tool Works Company600 West Main StreetTroy, OH 45373 USAFor Te

OM-230 455 Page 1SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USINGpom _4/05 Warning: Protect yourself and others from injury — read and follow thes

OM-230 455 Page 2 On inverter power sources, failed parts can ex-plode or cause other parts to explode whenpower is applied. Always wear a face shiel

OM-230 455 Page 31-3. Additional Symbols For Installation, Operation, And MaintenanceHOT PARTS can cause severe burns. Do not touch hot parts bare ha

OM-230 455 Page 41-5. Principal Safety StandardsSafety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,from Global Engineering Document

OM-230 455 Page 5SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATIONpom_fre 4/05 Avertissement : se protéger et protéger les autres contre le