Hobart-welding-products AIRFORCE 375 OM-2210 Uživatelský manuál

And Non-CE ModelsAirForce 375ProcessesDescriptionAir Plasma Cuttingand GougingAir Plasma CutterOM-2210 176 876NMarch 2001

OM-2210 Page 6D N’approchez pas le tube du chalumeau et l’arc pilote lorsque la gâchette estenfoncée.D Le câble de masse doit être pincé correctement

OM-2210 Page 71-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenanceDES PIECES CHAUDES peuvent pro-voquer d

OM-2210 Page 81-5. Information sur les champs électromagnétiquesDonnées sur le soudage électrique et sur les effets, pour l’organisme,des champs magné

OM-2210 Page 9SECTION 2 – DEFINITIONS2-1. Warning Label DefinitionsWarning! Watch Out! There arepossible hazards as shown by thesymbols.1 Cutting spar

OM-2210 Page 101 Warning! Watch Out! Thereare possible hazards asshown by the symbols.2 Incorrect voltage other thanspecified may damage unit(see Sect

OM-2210 Page 11SECTION 3 – INSTALLATION3-1. Specifications For Units Connected to a 20 Ampere, 115 Volt Circuit or a 10 Ampere,230 Volt CircuitAmperes

OM-2210 Page 123-4. Duty Cycle And Overheating For Non-CE ModelDuty Cycle is percentage of 10 min-utes that unit can cut at rated loadwithout overheat

OM-2210 Page 1318 in(457 mm)3-6. Selecting A Locationloc_2 3/96 - 801 303-C / 801 319-C1 Lifting HandleUse handle to lift unit.2 Hand CartUse cart or

OM-2210 Page 143-7. Connecting Work Clamp And Gas/Air SupplyRef. 801 319-C / Ref. 801 306-C1 Work Clamp2 WorkpieceConnect work clamp to a clean,paint-

OM-2210 Page 153-8. Setting Input Voltage Selector Switch And Connecting Input Power 801 304-C / 801 319-CCheck input voltage available at site.1 Inpu

Hobart Welders manufactures a full lineof welders and welding related equipment.For information on other quality Hobartproducts, contact your local Ho

OM-2210 Page 16SECTION 4 – OPERATION4-1. ControlsRef. 801 306-C / Ref. 192 4921 Output ControlUse control to set cutting output.The yellow zone is for

OM-2210 Page 174-2. Cutting SpeedThe cutting speed curves show therecommended maximum cuttingspeed capabilities of the powersource and torch for mild

OM-2210 Page 184-3. Sequence Of OperationPress trigger. Pilot arc starts.After cutting arc starts, slowlystart moving torch across metal.Adjust torch

OM-2210 Page 19SECTION 5 – MAINTENANCE & TROUBLESHOOTING5-1. Routine MaintenanceY Disconnect power before maintaining.. Maintain more oftenduring

OM-2210 Page 205-2. Overload Protection: Trouble Lights & Checking Shield Cup Shutdown SystemIf certain problems occur, theReady light goes off, a

OM-2210 Page 215-3. Torch And Work Cable ConnectionsIf torch or work cable needs to beremoved or replaced, proceed asfollows:Turn power Off, and disco

OM-2210 Page 225-4. TroubleshootingTrouble RemedyNo pilot arc; difficulty in establishing anClean or replace worn consumables as necessary (see torch

OM-2210 Page 23SECTION 6 – ELECTRICAL DIAGRAMFigure 6-1. Circuit Diagram For Power Source189 005-B

OM-2210 Page 24SECTION 7 – PARTS LISTFigure 7-1. Main Assembly. Hardware is common andnot available unless listed.ST-801 412-H

OM-2210 Page 25DescriptionPartNo.ItemNo.Figure 7-1. Main AssemblyQuantityDia.Mkgs.1 183 161 COVER, top 1. . . . . . . . . . . . . . . . . . . . . .

TABLE OF CONTENTSSECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING 1. . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1. . . .

OM-2210 Page 26DescriptionPartNo.ItemNo.Figure 7-1. Main Assembly (Continued)QuantityDia.Mkgs.38 +181 717 FRONT PANEL, (consisting of) 1. . . . . . .

Warranty Questions?Call1-877-HOBART1for your localHobart distributor.hobart retail 4/00ServiceYou always get the fast,reliable response youneed. Most

PRINTED IN USA  2000 Hobart Welding Products. 1/00Hobart Welding ProductsAn Illinois Tool Works Company600 West Main StreetTroy, OH 45373 USAFor Tech

dec_con1 1/96Declaration of Conformity forEuropean Community (CE) ProductsThis information is provided for units with CE certification (see rating lab

OM-2210 Page 1SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USINGpom _nd_5/971-1. Symbol UsageMeans Warning! Watch Out! There are possible hazardswith

OM-2210 Page 2Sparks and hot metal blow out from the cutting arc.Chipping and grinding cause flying metal.FLYING SPARKS can cause injury.D Wear approv

OM-2210 Page 31-3. Additional Symbols For Installation, Operation, And MaintenanceHOT PARTS can cause severe burns.D Do not touch hot parts bare hande

OM-2210 Page 41-4. Principal Safety StandardsSafety in Welding and Cutting, ANSI Standard Z49.1, from AmericanWelding Society, 550 N.W. LeJeune Rd, Mi

OM-2210 Page 5SECTION 1 – CONSIGNES DE SÉCURITÉ – LIRE AVANT UTILISATIONpom_nd_fre_5/971-1. Signification des symbolesSignifie Mise en garde ! Soyez