Hobart-welding-products H-9B Gun Uživatelský manuál Strana 1

H-9B GunOM-225 333A 2006−06ProcessesDescriptionMIG (GMAW) Welding (Optional)Flux Cored (FCAW) WeldingSemi-Automatic, Air-CooledFlux Cored (FCAW) And M

OM-225 333 Page 63-5. Threading Welding Wire1 Wire Spool2 Welding Wire3 Inlet Wire Guide4 Pressure Adjustment Knob5 Drive Roll6 Gun CableLay gun cable

OM-225 333 Page 7SECTION 4 − OPERATION4-1. Operating The GunRef. 804 240-A1 Trigger SwitchWhen pressed, energized wirefeeds and shielding gas flows (i

OM-225 333 Page 8SECTION 5 − MAINTENANCE & TROUBLESHOOTING5-1. Replacing Gun Contact TipRef. 804 241-AY Turn off welding power source.1 NozzleRemo

OM-225 333 Page 95-3. Replacing Gun LinerRef. 804 241-A / 803 497-A / 803 837-A / 803 899-ATools Needed:8 mm / 10 mmRemove nozzle. Cut off wireat cont

OM-225 333 Page 105-3. Replacing Gun Liner (Continued)When liner exits cable at gunhandle, guide liner into headtube. Continue to push liner untilit e

OM-225 333 Page 115-4. Replacing Switch/HandleY Turn Off welding power source.Disconnect switch leads and removeswitch. Connect leads to new switch(po

OM-225 333 Page 125-5. Removing Gun From Welding Power Source803 497-A / Ref. 803 378-A / 803 838-APull weld cable, trigger leads, and gas hosethrough

OM-225 333 Page 135-6. Routine MaintenanceY Turn Off welding power source before maintaining.Each Spool Of WireBlow OutGunCasingCleanNozzleAnd CheckCo

OM-225 333 Page 14SECTION 6 − PARTS LIST1804 243-A235 − See Table 6-14677Figure 6-1. H-9B GunDescriptionPartNo.225 397ItemNo.Figure 6-1. H-9B GunQuant

Warranty Questions?Call1-800-332-32817 AM − 6 PM ESThobart_warr 2/05ServiceYou always get the fast,reliable response youneed. Most replacementparts ca

Hobart Welders manufactures a full lineof welders and welding related equipment.For information on other quality Hobart products, contact your local H

PRINTED IN USA © 2005 Hobart Welding Products. 6/05Hobart Welding ProductsAn Illinois Tool Works Company600 West Main StreetTroy, OH 45373 USAFor Tech

TABLE OF CONTENTSSECTION 1 −SAFETY PRECAUTIONS FOR FCAW ANDGMAW WELDING GUNS − READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . .

OM-225 333 Page 1SECTION 1 −SAFETY PRECAUTIONS FOR FCAW ANDGMAW WELDING GUNS − READ BEFORE USINGSR7_8/031-1. Symbol UsageMeans Warning! Watch Out! The

OM-225 333 Page 2EMF INFORMATIONThe following is a quotation from the General Conclusions Section ofthe U.S. Congress, Office of Technology Assessment

OM-225 333 Page 3SECTION 2 − SAFETY INFORMATIONRead all safety messages throughout this manual.Obey all safety messages to avoid injury.Learn the mean

OM-225 333 Page 43-3. Installing Gun Into Welding Power Source803 497-A / Ref. 803 378-AOpen pressure assembly.Remove screws (3) fromcover, and remove

OM-225 333 Page 53-4. Installing Contact Tip And NozzleTools Needed:Ref. 804 241-AY Turn off welding power source.1 NozzleRemove nozzle.2 Contact Tip3